E3 NOR Flasher Multiple PS3 consoles Samsung Firmware

The E3 NOR Flasher is a very easy tool to downgrade or dual-boot your PS3. However your E3 hardware is limited to downgrading only 1 PS3 and was made for one time installation. However there is a firmware file that breaks this limit and allows you to downgrade unlimited consoles with only one E3 NOR Flasher.

Requirements
– E3 NOR Flasher (Must be installed in a PS3 -> Guide Here)
– Samsung Firmware File(Download Here)
– microSD card

Firmware Installation

First insert the microSD card in your computer and make sure it is formatted as fat32. Then download the firmware file (Here), extract the file and copy the file on your microSD card. When copied, insert the card in your E3Flasher:

Slide the empty cover to the right, this will unlock the cover:

E3sdcard1

Now lift the cover towards you :

E3sdcard2

Insert the microSD card like the picture below :

E3sdcard3

Now slice the cover to the left to lock the microSD card in place :

E3sdcard4

When the card is inserted, set the switches to “update mode” by setting the switches in the following direction :

Switch1 : Down
Switch2 : Down
Switch3 : Up
Switch4 : Up
Switch5 : Up
Switch6 : Up

e3samsungupdate

When done, turn on your PS3, 6 green Led’s and 1 red Led should turn on, then the blue leds will come on. This means the E3Flasher is updating it’s firmware. (if not, disconnect your eSata cable & try again)

E3NorFlasher_SamsungFirmwareHeader

When all blue led’s are on, click the “Reset” button under the blue leds to reset the E3Flasher.

e3samsungupdatedone

The blue leds should go off. Now turn off your PS3 and remove the microSD card. Then put the microSD card in your PC and check if the “update.bin” file has been removed, if not removed there should be a text file containing an error code added to your microSD card.

If the microSD card is empty, the update has been installed and you can now downgrade unlimited PS3’s with your E3Flasher!

25
Leave a Reply

Leave a Reply

  Subscribe  
newest oldest most voted
Notify of
Zeb
Guest
Zeb

THIS IS THE ONLY TUT WITH DOWNLOAD FILES THAT HELP THANK YOU SO VERY MUCH

Chio in gyu
Guest
Chio in gyu

thank you!!
Where can I buy E3 FLASHER

harvinlopez
Guest
harvinlopez

need help blue lights wont turn on
what can i do

kenny
Guest
kenny

Dont plug in the esata sata cable to the tp board

kenny
Guest
kenny

like how it is in the pic it happened to me too

Jay
Guest
Jay

Did this and it still not work on my PS3
Still getting same code for this and it did take the update

Rola3d
Guest
Rola3d

very useful tutorial.thanks very much.

Jadson
Guest
Jadson

Very useful tutorial. thanks very much. thanks very much. thanks very much.

andy_neukom
Guest
andy_neukom

after update i get 83 checks that are bad on my dump checker what do i do

OGKUSHNIGGA
Guest

THANK YOU!

Oliver
Guest
Oliver

So I can downgrade my ps3 to 3.55 with the flasher and remove it afterwards? Or has the flasher being left on the ps3?

rheimer van dijk
Guest
rheimer van dijk

every thing is on correct but when i turn my ps3 on with the update on the micro sd 6 green lights en one 1 will turn on but the blue lights wont show up after waithing an hour. my model numer is good en al that stuff i have an real e3 flasher. but it wont install the samsung firmware on the e3 flasher

Dj BooSt Q8
Guest

I have a new version of e3 flasher

When i do update process not taking the update file please any one help me

Sriyak Mukherjee
Guest

E 3 falsher not flashing light during update but no light (blue)
but update is success full as no bin file in memory card .

and during backup satrts
after pressing start in couple of sec it flash 11000100
1=blue light
0= no lite

and in memory card there is text file and wriiten there

start logging…
backup PS3 BIOS.
not original PS3